DWL@DWL10000340117

Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
1.4.0.0 * 23.07.2021 2 MB EXE AS4_HW_X20IF1041-1.exe
Popis V4.0 HW Upgrade (X20IF1041-1)

Revision information X20IF1041-1

Version 1.4.0.0:

ID:
Adaptations for Automation Studio 4.11
Channel description changed: no
Configuration description changed: yes
Firmware changed: no

Version 1.3.1.0:

ID: 721245
Expansion: Operation behind an X20(c)EM* possible
The module can now also be operated on an X20(c)EM*
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(29), 1\42761_1.fw(13)

Version 1.3.0.0:

ID: 482990
Module documentation revised
Data sheet V2.03
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 627865
Replacement of the interfacecard in AS
"ReplaceHW Modul" works correktly
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 717095
New FW V2.14.0.3_29
SDO and PDO transfer possible immediately after ModulOK = TRUE
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(29), 1\42761_1.fw(13)

Version 1.2.1.0:

ID: 466580
FDT/DTM Cycle Time change
Change parameter name "Cycle time [µs]" to "Data exchange time(CPU-netX) [µs]"
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 466585
Add ModulOK in I/O Mapping
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.2.0.0:

ID: 459055 / Support ID: 400149579
X20IF1061-1: NetX: Cyclic statusbits wrong when cable is disconnected
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.1.3.0:

ID: 422290 / Support ID: 400143565
Wrong SDO handling causes in rare cases stop of the Interface card.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(25), 1\42761_1.fw(12)

Version 1.1.2.0:

ID: 263655 / Support ID: 400069676
Incorrect error message when writing SDOs
If an SDO write request on the CAN bus returns error message 0x08000024 (noaccess to flash memory), then this is not received in this form in the nxcomSdoWrite() function block. The nxcomSdoWrite() function incorrectly returns error message 0xC0420028 (general fault during SDO transfer).
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 376165 / Support ID: 400129930
Frequent transmission of Start command by nxcomNmt function block causing aproblem in mailbox or master
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(24), 1\42761_1.fw(12)

Version 1.1.1.1:

ID:366170
EPLAN-datas got conformed
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(22), 1\42761_1.fw(12)

Version 1.1.0.3:

ID: 263645 / Support ID: 400069675
CANopen master doesn't write output data toall slaves
When using a special configuration with several CANopen slaves the output data is only written to the first slave.
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:Yes
Firmware: 1\42761a1.fw(21), 1\42761_1.fw(12)

Version 1.1.0.1:

ID: 259320
Vendor ID changed
Module identifies with B+R Vendor ID now
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(20), 1\42761_1.fw(12)

Version 1.0.3.0:

ID: 240405
X20 Interface CANopen Master, Configuration of netX cycle time
X20 Interface CANopen Master, Configuration of netX cycle time.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.2.0:

ID: 239395 / Support ID: 400051057
Interface module CANopen master: Output datanot written by all CANopen slaves
Interface module CANopen master: Output data not written by all CANopen slaves
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.1.0:

ID:235825
Interface module CANopen master, first version
Interface module CANopen master, first version
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(17), 1\42761_1.fw(12)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
1.3.0.0 * 18.02.2021 2 MB EXE AS4_HW_X20IF1041-1.exe
Popis V4.0 HW Upgrade (X20IF1041-1)

Revision information X20IF1041-1

Version 1.3.0.0:

ID: 482990
Module documentation revised
Data sheet V2.03
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 627865
Replacement of the interfacecard in AS
"Replace HW Modul" works correktly
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 717095
New FW V2.14.0.3_29
SDO and PDO transfer possible immediately after ModulOK = TRUE
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(29), 1\42761_1.fw(13)

Version 1.2.1.0:

ID: 466580
FDT/DTM Cycle Time change
Change parameter name "Cycle time [µs]" to "Data exchange time (CPU-netX) [µs]"
Channel description changed: No
Configuration description changed: Yes
Firmwarechanged: No

ID: 466585
Add ModulOK in I/O Mapping
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.2.0.0:

ID: 459055 / Support ID: 400149579
X20IF1061-1: NetX: Cyclic statusbits wrong when cable is disconnected
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.1.3.0:

ID: 422290 / Support ID: 400143565
Wrong SDO handling causes in rare cases stop of the Interface card.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(25), 1\42761_1.fw(12)

Version 1.1.2.0:

ID: 263655 / Support ID: 400069676
Incorrect error message when writing SDOs
If an SDO write request on the CAN bus returns error message 0x08000024 (noaccess to flash memory), then this is not received in this form in the nxcomSdoWrite() function block. The nxcomSdoWrite() function incorrectly returns error message 0xC0420028 (general fault during SDO transfer).
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 376165 / Support ID: 400129930
Frequent transmission of Start command by nxcomNmt function block causing aproblem in mailbox or master
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(24), 1\42761_1.fw(12)

Version 1.1.1.1:

ID: 366170
EPLAN-datas got conformed
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(22), 1\42761_1.fw(12)

Version 1.1.0.3:

ID: 263645 / Support ID: 400069675
CANopen master doesn't write output data to all slaves
When using a special configuration with several CANopen slaves the output data is only written to the first slave.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(21), 1\42761_1.fw(12)

Version 1.1.0.1:

ID: 259320
Vendor ID changed
Module identifies with B+R Vendor ID now
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(20), 1\42761_1.fw(12)

Version 1.0.3.0:

ID: 240405
X20 Interface CANopen Master, Configuration of netX cycle time
X20 Interface CANopen Master, Configuration of netX cycle time.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.2.0:

ID: 239395 / Support ID: 400051057
Interface module CANopen master: Output data not written by all CANopen slaves
Interface module CANopen master: Output data not written by all CANopen slaves
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.1.0:

ID: 235825
Interface module CANopen master, first version
Interface module CANopen master, first version
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(17), 1\42761_1.fw(12)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
1.2.1.0 * 19.02.2016 865 KB EXE AS4_HW_X20IF1041-1.exe
Popis V4.0 HW Upgrade (X20IF1041-1)

Revision information X20IF1041-1

Version 1.2.1.0:

ID: 466580
FDT/DTM Cycle Time change
Change parameter name "Cycle time [µs]" to "Data exchange time (CPU-netX) [µs]"
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 466585
Add ModulOK in I/O Mapping
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.2.0.0:

ID: 459055 / Support ID: 400149579
X20IF1061-1: NetX: Cyclic statusbits wrong when cable is disconnected
Channeldescription changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12)

Version 1.1.3.0:

ID: 422290 / Support ID: 400143565
Wrong SDO handling causes in rare cases stop of the Interface card.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(25), 1\42761_1.fw(12)

Version 1.1.2.0:

ID: 263655 / Support ID: 400069676
Incorrect error message when writing SDOs
If an SDO write request on the CAN bus returns error message 0x08000024 (noaccess to flash memory), then this is not received in this form in the nxcomSdoWrite() function block. The nxcomSdoWrite() function incorrectly returns error message 0xC0420028 (general fault during SDO transfer).
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 376165 / Support ID: 400129930
Frequent transmission of Start command by nxcomNmt function block causing aproblem in mailbox or master
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(24), 1\42761_1.fw(12)

Version 1.1.1.1:

ID: 366170
EPLAN-datas got conformed
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(22), 1\42761_1.fw(12)

Version 1.1.0.3:

ID: 263645 / Support ID: 400069675
CANopen master doesn't write output data to all slaves
Whenusing a special configuration with several CANopen slaves the output data is only written to the first slave.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(21), 1\42761_1.fw(12)

Version 1.1.0.1:

ID: 259320
Vendor ID changed
Module identifies with B+R Vendor ID now
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(20), 1\42761_1.fw(12)

Version 1.0.3.0:

ID: 240405
X20 Interface CANopen Master, Configuration of netX cycle time
X20 Interface CANopen Master, Configuration of netX cycle time.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(18),1\42761_1.fw(12)

Version 1.0.2.0:

ID: 239395 / Support ID: 400051057
Interface module CANopen master: Output data not written by all CANopen slaves
Interface module CANopen master: Output data not written byall CANopen slaves
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.1.0:

ID: 235825
Interface module CANopen master, first version
Interface module CANopen master, first version
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(17), 1\42761_1.fw(12)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
1.1.1.1 * 17.03.2014 581 KB EXE AS4_HW_X20IF1041-1.exe
Popis V4.0 HW Upgrade (X20IF1041-1)

Revision information X20IF1041-1

Version 1.1.1.1:

ID: 366170
EPLAN-datas got conformed
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(22), 1\42761_1.fw(12)

Version 1.1.0.3:

ID: 263645 / Support ID: 400069675
CANopen masterdoesn't write output data to all slaves
When using a special configuration with several CANopen slaves the output data is only written to the first slave.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(21), 1\42761_1.fw(12)

Version 1.1.0.1:

ID: 259320
Vendor ID changed
Module identifies with B+R Vendor ID now
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(20), 1\42761_1.fw(12)

Version 1.0.3.0:

ID:240405
X20 Interface CANopen Master, Configuration of netX cycle time
X20 Interface CANopen Master, Configuration of netX cycle time.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.2.0:

ID: 239395 / Support ID: 400051057
Interface module CANopen master: Output data not written by all CANopen slaves
Interfacemodule CANopen master: Output data not written by all CANopen slaves
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12)

Version 1.0.1.0:

ID: 235825
Interface module CANopen master, first version
Interface module CANopen master, first version
Channel description changed: No
Configuration description changed: No
Firmwarechanged: Yes
Firmware: 1\42761a1.fw(17), 1\42761_1.fw(12)
Loading
Zpět k seznamu

Vyberte prosím zemi a jazyk

B&R Logo