|
0TG1000.01
|
Аппаратный ключ Technology Guard (MSD)
|
|
|
0TG1000.02
|
Аппаратные ключи Technology Guard (HID)
|
|
|
0TGF016.01
|
Аппаратный ключ Technology Guard (MSD), со встроенным флеш-накопителем, 16 ГБ (MLC)
|
|
|
1TG0500.01
|
License for PVI Runtime (SW). Requires installation of a SW container Technology Guard. One license per target system is required.
|
|
|
1TG0500.02
|
License for PVI Runtime (TG). Technology Guard hardware additionally required. One license per target system is required.
|
|
|
1TG10X0.1
|
TG license for controller redundancy - Changeover times within a few milliseconds - Synchronization with microsecond accuracy - Seamless integration via X20 redundancy link interface - No special controller hardware, standard X20 controller - One-click configuration - Bumpless software download - Non-reactive component exchange during operation B&R controller redundancy ensures the highest availability in machine, process, plant and infrastructure automation. A redundant controller consists of two assemblies (primary/secondary) with identical hardware. If one of the controllers fails, then a bumpless redundancy switchover to the other controller takes places automatically. Important: Two licenses (two controllers) are required for a redundancy system!
|
|
|
1TG4600.00
|
License for Automation Runtime Simulation (TG). Technology Guard hardware additionally required. One license per target system is required.
|
|
|
1TG4600.01
|
License for Automation Runtime Simulation (SW). Requires installation of a SW container Technology Guard. One license per target system is required. This license is supported starting with version 4.9.
|
|
|
1TG4600.10-5
|
Лицензия Automation Runtime Windows TG
|
|
|
1TG4600.20
|
Automation Runtime Windows Desktop TG license
|
|
|
1TG4601.06-5
|
Automation Runtime Embedded, лицензия TG
|
|
|
1TG4601.06-T
|
Automation Runtime Embedded, терминал, лицензия TG
|
|
|
1TG4700.00
|
Гипервизор B&R
|
|
|
1TG7110.M
|
Advanced Controller Tuning TG license - Model-based closed loop control procedure
|
|
|
1TG7111.M
|
Advanced Model Identification TG license - Identification of the controlled system
|
|
|
1TG7120.M
|
TG license for advanced signal processing
|
|
|
1TG7210.M
|
Temperature Control TG license - Heating and cooling processes - Fully automatic control tuning procedure - Automatic multi-zone synchronization - Control with minimal overshooting - Kalman filter - Temperature setpoint generator - Simulation model
|
|
|
1TG7310.M
|
Valve-based hydraulic control TG license - Position and speed control - Alternating pressure/force control - Valve servo correction - Simulation model for a hydraulic drive
|
|
|
1TG7350.M
|
Hydraulic Servo Pump Control TG license - Alternating speed/pressure control for the hydraulic pump - Pump protection - Overview of features - Simulation model for a hydraulic drive
|
|
|
1TG7410.M
|
Winder Control TG license - Dancer position control - Tension control - Web accumulator control - Diameter estimation - Inertia compensation - Dynamic preset tension - Simulation model
|
|
|
1TG7430.M
|
Tension Control TG license - Multi-zone tension control - Individual preset tension for each zone - Automatic control parameter tracking - Acceleration compensation - Simulation model
|
|
|
1TG7450.1
|
TG license for register control (legacy) - Key and sequential color registration - Independent of substrate - Automatic control parameter tracking - Acceleration compensation - Simulation model
|
|
|
1TG8CNC0000.00-01
|
ARNC0 license (existing range of functions) - Path control (CNC) for 1 CNC channel with up to 4 axes Configurable syntax interpreter for: - CNC programs based on DIN/ISO 66025 - ST-based robotics programs - Application-specific functions Powerful geometric and dynamic path planning, optimal contour precision Automatic tangential axis Tool compensation Workspace monitoring Path-accurate restart functions Forward/Backward movements on the path Path-synchronous control signals No authorization required to export this version
|
|
|
1TG8CNC0000.00-02
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 2 CNC channels with up to 4 axes Configurable syntax interpreter for: - CNC programs based on DIN/ISO 66025 - ST-based robotics programs - Application-specific functions Powerful geometric and dynamic path planning, optimal contour precision Automatic tangential axis Tool compensation Workspace monitoring Path-accurate restart functions Forward/Backward movements on the path Path-synchronous control signals Required: 1TG8TRF0000.01-xx No authorization required to export this version
|
|
|
1TG8CNC0000.00-04
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 4 CNC channels with up to 4 axes Configurable syntax interpreter for: - CNC programs based on DIN/ISO 66025 - ST-based robotics programs - Application-specific functions Powerful geometric and dynamic path planning, optimal contour precision Automatic tangential axis Tool compensation Workspace monitoring Path-accurate restart functions Forward/Backward movements on the path Path-synchronous control signals No authorization required to export this version
|
|
|
1TG8CNC0000.00-08
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 8 CNC channels with up to 4 axes Configurable syntax interpreter for: - CNC programs based on DIN/ISO 66025 - ST-based robotics programs - Application-specific functions Powerful geometric and dynamic path planning, optimal contour precision Automatic tangential axis Tool compensation Workspace monitoring Path-accurate restart functions Forward/Backward movements on the path Path-synchronous control signals No authorization required to export this version
|
|
|
1TG8CNC0000.00-09
|
ARNC0 license (existing range of functions) - Path control (CNC) for more than 8 CNC channels with up to 4 axes Configurable syntax interpreter for: - CNC programs based on DIN/ISO 66025 - ST-based robotics programs - Application-specific functions Powerful geometric and dynamic path planning, optimal contour precision Automatic tangential axis Tool compensation Workspace monitoring Path-accurate restart functions Forward/Backward movements on the path Path-synchronous control signals No authorization required to export this version
|
|
|
1TG8CNC0000.01-01
|
ARNC0 license (existing range of functions) - Path control (CNC) for 1 CNC channel with up to 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNC0000.01-02
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 2 CNC channels with up to 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNC0000.01-04
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 4 CNC channels with up to 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNC0000.01-08
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 8 CNC channels with up to 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Requirement: 1TG8TRF0000.01-01 Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNC0000.01-09
|
ARNC0 license (existing range of functions) - Path control (CNC) for more than 8 CNC channels with up to 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNCAX00.01-01
|
ARNC0 license (existing range of functions) - Path control (CNC) for 1 CNC channel with more than 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNCAX00.01-02
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 2 CNC channels with more than 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNCAX00.01-04
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 4 CNC channels with more than 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNCAX00.01-08
|
ARNC0 license (existing range of functions) - Path control (CNC) for up to 8 CNC channels with more than 9 axes Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8CNCAX00.01-09
|
ARNC0 license (existing range of functions) - Path control (CNC) for more than 8 CNC channels with more than 9 axes Total number of CNC channels and kinematic structures used: Max. 8 Configurable syntax interpreter for - CNC programs per DIN/ISO 66025 - Robotics programs per ST - Application-specific functions Powerful geometric and dynamic path planning, optimum contour precision Automatic tangential axis Tool compensation Workspace monitoring Path precision for restart functions Forward/reverse movement on the path Path-synchronous control signals Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8COL0000.01-01
|
3D collision detection - 1 external kinematic structure
|
|
|
1TG8COL0000.01-02
|
3D collision detection - 2 external kinematic structures
|
|
|
1TG8COL0000.01-04
|
3D collision detection - 4 external kinematic structures
|
|
|
1TG8COL0000.01-08
|
3D collision detection - 8 external kinematic structures
|
|
|
1TG8COL0000.01-09
|
3D collision detection - External kinematic structures
|
|
|
1TG8SDC0000.01-01
|
SDC software ClosedLoop license for 1 independent positioning axis Application for devices with: - Speed interface (AO) - Absolute position interface and enabled position controller Application examples: - Stepper motor and motor modules - Frequency inverters - Servo drive from other vendors
|
|
|
1TG8SDC0000.01-02
|
SDC software ClosedLoop license for up to 2 independent positioning axes Application for devices with: - Speed interface (AO) - Absolute position interface and enabled position controller Application examples: - Stepper motor and motor modules - Frequency inverters - Servo drive from other vendors
|
|
|
1TG8SDC0000.01-04
|
SDC software ClosedLoop license for up to 4 independent positioning axes Application for devices with: - Speed interface (AO) - Absolute position interface and enabled position controller Application examples: - Stepper motor and motor modules - Frequency inverters - Servo drive from other vendors
|
|
|
1TG8SDC0000.01-08
|
SDC software ClosedLoop license for up to 8 independent positioning axes Application for devices with: - Speed interface (AO) - Absolute position interface and enabled position controller Application examples: - Stepper motor and motor modules - Frequency inverters - Servo drive from other vendors
|
|
|
1TG8SDC0000.01-09
|
SDC software ClosedLoop license for more than 8 independent positioning axes Application for devices with: - Speed interface (AO) - Absolute position interface and enabled position controller Application examples: - Stepper motor and motor modules - Frequency inverters - Servo drive from other vendors
|
|
|
1TG8SDC0000.02-01
|
SDC software Advanced license for 1 independent positioning axis Functions: - Electronic gears - Cams - Cam Profile Automat - ACOPOS reACTION Technology
|
|
|
1TG8SDC0000.02-02
|
SDC software Advanced license for up to 2 independent positioning axes Functions: - Electronic gears - Cams - Cam Profile Automat - ACOPOS reACTION Technology
|
|
|
1TG8SDC0000.02-04
|
SDC software Advanced license for up to 4 independent positioning axes Functions: - Electronic gears - Cams - Cam Profile Automat - ACOPOS reACTION Technology
|
|
|
1TG8SDC0000.02-08
|
SDC software Advanced license for up to 8 independent positioning axes Functions: - Electronic gears - Cams - Cam Profile Automat - ACOPOS reACTION Technology
|
|
|
1TG8SDC0000.02-09
|
SDC software Advanced license for more than 8 independent positioning axes Functions: - Electronic gears - Cams - Cam Profile Automat - ACOPOS reACTION Technology
|
|
|
1TG8SDC0000.03-01
|
SDC software Premium license for 1 independent positioning axis Function: - Cycle time less than 800 µs
|
|
|
1TG8SDC0000.03-02
|
SDC software Premium license for up to 2 independent positioning axes Function: - Cycle time less than 800 µs
|
|
|
1TG8SDC0000.03-04
|
SDC software Premium license for up to 4 independent positioning axes Function: - Cycle time less than 800 µs
|
|
|
1TG8SDC0000.03-08
|
SDC software Premium license for up to 8 independent positioning axes Function: - Cycle time less than 800 µs
|
|
|
1TG8SDC0000.03-09
|
SDC software Premium license for more than 8 independent positioning axes Function: - Cycle time less than 800 µs
|
|
|
1TG8TRF0000.01-01
|
3D transformation functions License for 1 kinematic structure with up to 4 joint axes - SCARA - Double SCARA - 2D rod kinematics - Tripod Interface support for user-specific transformations with up to 4 or more joint axes Required: - CNC/Robotics 1TG8CNC0000.00-xx (up to 4 joint axes) - CNC/Robotics 1TG8CNC0000.01-xx (up to 9 joint axes) - CNC/Robotics 1TG8CNCAX00.00-xx (more than 9 joint axes) No authorization required to export this version
|
|
|
1TG8TRF0000.01-02
|
3D transformation functions License for up to 2 kinematic structures with up to 4 joint axes - SCARA - Double SCARA - 2D rod kinematics - Tripod Interface support for user-specific transformations with up to 4 or more joint axes Required: - CNC/Robotics 1TG8CNC0000.00-xx (up to 4 joint axes) - CNC/Robotics 1TG8CNC0000.01-xx (up to 9 joint axes) - CNC/Robotics 1TG8CNCAX00.00-xx (more than 9 joint axes) No authorization required to export this version
|
|
|
1TG8TRF0000.01-04
|
3D transformation functions License for up to 4 kinematic structures with up to 4 joint axes - SCARA - Double SCARA - 2D rod kinematics - Tripod Interface support for user-specific transformations with up to 4 or more joint axes Required: - CNC/Robotics 1TG8CNC0000.00-xx (up to 4 joint axes) - CNC/Robotics 1TG8CNCAX00.00-xx (more than 4 joint axes) No authorization required to export this version
|
|
|
1TG8TRF0000.01-08
|
3D transformation functions License for up to 8 kinematic structures with up to 4 joint axes - SCARA - Double SCARA - 2D rod kinematics - Tripod Interface support for user-specific transformations with up to 4 or more joint axes Required: - CNC/Robotics 1TG8CNC0000.00-xx (up to 4 joint axes) - CNC/Robotics 1TG8CNC0000.01-xx (up to 9 joint axes) - CNC/Robotics 1TG8CNCAX00.00-xx (more than 9 joint axes) No authorization required to export this version
|
|
|
1TG8TRF0000.01-09
|
3D transformation function License for up to 9 or more kinematic structures with up to 4 joint axes - SCARA - Double SCARA - 2D rod kinematics - Tripod Interface support for user-specific transformations with up to 4 or more joint axes Required: - CNC/Robotics 1TG8CNC0000.00-xx (up to 4 joint axes) - CNC/Robotics 1TG8CNCAX00.00-xx (more than 4 joint axes) No authorization required to export this version
|
|
|
1TG8TRF0000.02-01
|
3D transformation functions License for 1 kinematic structure with more than 4 joint axes - 6-axis articulated arm - 5-axis CNC - Galileo Interface support for user-specific transformations Requirement: CNC/Robotics 1TG8CNCAX00.01-xx Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8TRF0000.02-02
|
3D transformation functions License for up to 2 kinematic structures with more than 4 joint axes - 6-axis articulated arm - 5-axis CNC - Galileo Interface support for user-specific transformations Requirement: CNC/Robotics 1TG8CNCAX00.01-xx Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8TRF0000.02-04
|
3D transformation functions License for up to 4 kinematic structures with more than 4 joint axes - 6-axis articulated arm - 5-axis CNC - Galileo Interface support for user-specific transformations Requirement: CNC/Robotics 1TG8CNCAX00.01-xx Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8TRF0000.02-08
|
3D transformation functions License for up to 8 kinematic structures with more than 4 joint axes - 6-axis articulated arm - 5-axis CNC - Galileo Interface support for user-specific transformations Requirement: CNC/Robotics 1TG8CNCAX00.01-xx Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TG8TRF0000.02-09
|
3D transformation functions License for more than 8 kinematic structures with more than 4 joint axes - 6-axis articulated arm - 5-axis CNC - Galileo Interface support for user-specific transformations Requirement: CNC/Robotics 1TG8CNCAX00.01-xx Authorization required to export this version Regulation (EC) 2021/821 (dual use): 2D002 This license is subject to special terms of use and can only be used in conjunction with library ARNC0ext. ARNC0ext must be requested from B&R.
|
|
|
1TGACP0000.00-01
|
License for 1 ACOPOS P3 technology function per axis Examples for technology functions: - Virtual axis - Closed-loop control of elastic systems - Pitch error and backlash compensation - Repetitive control - ISQ ripple identification - ACOPOS reACTION - SafeMOTION with motors from 3rd-party vendors - ...
|
|
|
1TGACP0000.00-99
|
General license for all ACOPOS P3 technology functions and networked SafeMOTION packages per axis
|
|
|
1TGACPSMC0.00-01
|
License for one Networked SafeMOTION package per axis Examples for Networked SafeMOTION packages: - Velocity (safety functions SOS, SS2, SLS, SMS, SLA) - Position (safety functions, SLP, SMP, RSP) - Advanced (safety functions SBT, SLT, SLI, SDI) - Etc.
|
|
|
1TGAP42CDRV9992UPG
|
PROFIBUS DP PROFINET/CTRL, UPG
|
|
|
1TGAP42CDRV9993NEW
|
Modbus-RTU/ TCP/CTRL/CC, NEW Important notice: The driver for the Control Computer (CC) is still in the prototype phase, use only permitted for non-productive systems after release by product management!
|
|
|
1TGAP42CDRV9993UPG
|
Modbus-RTU/ TCP/CTRL/CC, UPG Important notice: The driver for the Control Computer (CC) is still in the prototype phase, use only permitted for non-productive systems after release by product management!
|
|
|
1TGAP42CDRV9998UPG
|
IEC 60870-5-104/CTRL/CC, UPG Important note: The driver for the control computer (CC) is still in the prototype phase. Use is only permitted for non-productive systems after approval by the product management!
|
|
|
1TGAP42CDRV9999NEW
|
IEC 60870-5-101 / CTRL, NEW
|
|
|
1TGAP42CDRV9999UPG
|
IEC 60870-5-101 / CTRL, UPG
|
|
|
1TGAP42CLIB9995NEW
|
MPC signal (MIMO) / CTRL, NEW APROL MPC (multiple In / multiple Out) / CTRL This license is valid for activation of 1 controlled variable (X), 1 manipulated variable (Y) or 1 disturbance variable input (Z). Example: 7 licenses are therefore needed for an MPC with 2xX, 3xZ and 2xY. The license allows the use of APROL basic functions on a B&R controller (SG4 target system). To use the license on a controller, a dongle of type 0TG1000.02 (Technology Guard) is required.
|
|
|
1TGAP42CLIB9997NEW
|
Process Automation Lib. (PAL) / CTRL, NEW
|
|
|
1TGAP42CLIB9997UPG
|
Process Automation Lib. (PAL) / CTRL, UPG
|
|
|
1TGAP42CLIB9998UPG
|
Basic Library/CTRL, UPG
|
|
|
1TGAP42CLIB9999NEW
|
SelfTuningAlgorith-MinInvasive/CTRL, NEW
|
|
|
1TGAP42E0000000NEW
|
Engineering,NEW Engineering system is used to prepare configuration data for the whole project before it is deployed to runtime server.
|
|
|
1TGAP42E0000000OEM
|
Engineering,OEM Engineering system is used to prepare configuration data for the whole project before it is deployed to runtime server.
|
|
|
1TGAP42E0000000UPG
|
Engineering,UPG Engineering system is used to prepare configuration data for the whole project before it is deployed to runtime server.
|
|
|
1TGAP42EAS-0000NEW
|
Engineering AS Edition APROL,NEW
|
|
|
1TGAP42EAS-0000UPG
|
Engineering AS Edition APROL,UPG
|
|
|
1TGAP42O0000000NEW
|
Operator,NEW Operations stations provide the user interface for operators (process graphics, faceplates, trend displays, alarm & event lists, etc.).
|
|
|
1TGAP42O0000000OEM
|
Operator,OEM
|
|
|
1TGAP42O0000000UPG
|
Operator,UPG Operations stations provide the user interface for operators (process graphics, faceplates, trend displays, alarm & event lists, etc.).
|
|
|
1TGAP42ONET0001UPG
|
Operator via Net, UPG
|
|
|
1TGAP42R0001111NEW
|
ParameterCenter, NEW
|
|
|
1TGAP42R0001111UPG
|
ParameterCenter, UPG
|
|
|
1TGAP42RBI-1111NEW
|
Business Intellig. R (+E)- SOLUTIONS, NEW License for one instance of Report Server(R) and Report Designer(E). The report server generates reports from the data in use, data at rest or data in transit. Provides report creation and viewing, ad hoc reports and mobile access. Includes a license for "TIBCO JasperReports Server Professional Edition" for APROL (package/bundle for OEM). - B&R offers this license as an integrated software vendor (OEM) exclusively as an optional license for APROL. This license is only permitted to be used together with APROL. - This license is a 1-year subscription and permits the operation of the "TIBCO JasperReports Server Professional Edition" software that is shipped with APROL for an unlimited period of time (OEM license does not expire). - The 1-year subscription begins with the delivery of the APROL system by B&R. - If the "TIBCO JasperReports Server Professional Edition" software is updated/upgraded after the 1-year subscription has expired, a new license (subscription) is required (e.g. caused by the APROL update/upgrade). - Customers who will use the monthly AutoYaST update via license "GPOS- Security update- 202x/ CC" in the future must ensure that a "JRS BI- Security update- 202x" license may also have to be purchased. Note: - The service life of the "TIBCO JasperReports Server Professional Edition" software is not limited. - If the software is updated, however the control computer must have a valid 1-year subscription at that moment.
|
|
|
1TGAP42RBI-1111UPG
|
Business Intellig. R (+E)- SOLUTIONS, UPG License for one instance of Report Server(R) and Report Designer(E). The report server generates reports from the data in use, data at rest or data in transit. Provides report creation and viewing, ad hoc reports and mobile access. Includes a license for "TIBCO JasperReports Server Professional Edition" for APROL (package/bundle for OEM). - B&R offers this license as an integrated software vendor (OEM) exclusively as an optional license for APROL. This license is only permitted to be used together with APROL. - This license is a 1-year subscription and permits the operation of the "TIBCO JasperReports Server Professional Edition" software that is shipped with APROL for an unlimited period of time (OEM license does not expire). - The 1-year subscription begins with the delivery of the APROL system by B&R. - If the "TIBCO JasperReports Server Professional Edition" software is updated/upgraded after the 1-year subscription has expired, a new license (subscription) is required (e.g. caused by the APROL update/upgrade). - Customers who will use the monthly AutoYaST update via license "GPOS- Security update- 202x/ CC" in the future must ensure that a "JRS BI- Security update- 202x" license may also have to be purchased. Note: - The service life of the "TIBCO JasperReports Server Professional Edition" software is not limited. - If the software is updated, however the control computer must have a valid 1-year subscription at that moment.
|
|
|
1TGAP42RBI-9999NEW
|
Business Intelligence R (+E)- DCS, NEW License for one instance of Report Server(R) and Report Designer(E). The report server generates reports from the data in use, data at rest or data in transit. Provides report creation and viewing, ad hoc reports and mobile access. Includes a license for "TIBCO JasperReports Server Professional Edition" for APROL (package/bundle for OEM). - B&R offers this license as an integrated software vendor (OEM) exclusively as an optional license for APROL. This license is only permitted to be used together with APROL. - This license is a 1-year subscription and permits the operation of the "TIBCO JasperReports Server Professional Edition" software that is shipped with APROL for an unlimited period of time (OEM license does not expire). - The 1-year subscription begins with the delivery of the APROL system by B&R. - If the "TIBCO JasperReports Server Professional Edition" software is updated/upgraded after the 1-year subscription has expired, a new license (subscription) is required (e.g. caused by the APROL update/upgrade). - Customers who will use the monthly AutoYaST update via license "GPOS- Security update- 202x/ CC" in the future must ensure that a "JRS BI- Security update- 202x" license may also have to be purchased. Note: - The service life of the "TIBCO JasperReports Server Professional Edition" software is not limited. - If the software is updated, however the control computer must have a valid 1-year subscription at that moment.
|
|
|
1TGAP42RBI-9999UPG
|
Business Intelligence R (E)- DCS, UPG License for one instance of Report Server(R) and Report Designer(E). The report server generates reports from the data in use, data at rest or data in transit. Provides report creation and viewing, ad hoc reports and mobile access. Includes a license for "TIBCO JasperReports Server Professional Edition" for APROL (package/bundle for OEM). - B&R offers this license as an integrated software vendor (OEM) exclusively as an optional license for APROL. This license is only permitted to be used together with APROL. - This license is a 1-year subscription and permits the operation of the "TIBCO JasperReports Server Professional Edition" software that is shipped with APROL for an unlimited period of time (OEM license does not expire). - The 1-year subscription begins with the delivery of the APROL system by B&R. - If the "TIBCO JasperReports Server Professional Edition" software is updated/upgraded after the 1-year subscription has expired, a new license (subscription) is required (e.g. caused by the APROL update/upgrade). - Customers who will use the monthly AutoYaST update via license "GPOS- Security update- 202x/ CC" in the future must ensure that a "JRS BI- Security update- 202x" license may also have to be purchased. Note: - The service life of the "TIBCO JasperReports Server Professional Edition" software is not limited. - If the software is updated, however the control computer must have a valid 1-year subscription at that moment.
|
|
|
1TGAP42RGV-0050NEW
|
GV-License-Runtime 0050 GVs, NEW
|
|
|
1TGAP42RGV-0050UPG
|
GV-License-Runtime 0050 GVs, UPG
|
|
|
1TGAP42RGV-1000NEW
|
GV-License-Runtime 1000 GVs, NEW
|
|
|
1TGAP42RGV-1000UPG
|
GV-License-Runtime 1000 GVs, UPG
|
|
|
1TGAP42RIO-0050NEW
|
IO-License-Runtime 0050 I/Os, NEW
|
|
|
1TGAP42RIO-0050UPG
|
IO-License-Runtime 0050 I/Os, UPG
|
|
|
1TGAP42RIO-1000NEW
|
IO-License-Runtime 1000 I/Os, NEW
|
|
|
1TGAP42RIO-1000UPG
|
IO-License-Runtime 1000 I/Os, UPG
|
|
|
1TGAP42RLIB9996NEW
|
PAL Edition PDA (PAL-PDA)/CC, NEW
|
|
|
1TGAP42RLIB9996UPG
|
PAL Edition PDA (PAL-PDA)/CC, UPG
|
|
|
1TGAP42RNET1111NEW
|
SQL access Historian Database, NEW
|
|
|
1TGAP42RNET1111UPG
|
SQL access Historian Database, UPG
|
|
|
1TGAP42RNET1112NEW
|
OPC access Realtime-Database, NEW
|
|
|
1TGAP42RNET1112UPG
|
OPC access Realtime-Database, UPG
|
|
|
1TGAP42RRED0000NEW
|
Runtime Redundancy,NEW
|
|
|
1TGAP42RRED0000OEM
|
Runtime Redundancy,OEM
|
|
|
1TGAP42RRED0000UPG
|
Runtime Redundancy,UPG
|
|
|
1TGAP42RREDEDUCAT
|
Runtime Redundancy,Education key
|
|
|
1TGAP42RREDINTERN
|
Runtime Redundancy,Internal use key
|
|
|
1TGAP42RREDPARTNER
|
Runtime Redundancy,Partner key
|
|
|
1TGAP42RRGV0050NEW
|
GV-License-Red.Capability 0050 GVs, NEW
|
|
|
1TGAP42RRGV0050UPG
|
GV-License-Red.Capability 0050 GVs, UPG
|
|
|
1TGAP42RRGV1000NEW
|
GV-License-Red.Capability 1000 GVs, NEW
|
|
|
1TGAP42RRGV1000UPG
|
GV-License-Red.Capability 1000 GVs, UPG
|
|
|
1TGAP42RRIO0050NEW
|
IO-License-Red.Capability 0050 I/Os, NEW
|
|
|
1TGAP42RRIO0050UPG
|
IO-License-Red.Capability 0050 I/Os, UPG
|
|
|
1TGAP42RRIO1000NEW
|
IO-License-Red.Capability 1000 I/Os, NEW
|
|
|
1TGAP42RRIO1000UPG
|
IO-License-Red.Capability 1000 I/Os, UPG
|
|
|
1TGAP42RSVR0000NEW
|
Runtime server,NEW Runtime server provides the system’s runtime core DCS functions (alarm system, trend system, realtime database).
|
|
|
1TGAP42RSVR0000OEM
|
Runtime server,OEM Runtime server provides the system’s runtime core DCS functions (alarm system, trend system, realtime database).
|
|
|
1TGAP42RSVR0000UPG
|
Runtime server,UPG Runtime server provides the system’s runtime core DCS functions (alarm system, trend system, realtime database).
|
|
|
1TGAP42XEDUCATION
|
Runtime/Operator/Engineering, Education
|
|
|
1TGAP42XPARTNER
|
Runtime/Operator/Engineering, partner key This license is intended for engineering and commissioning purposes for B&R Qualified Partners. It is not permitted to be used permanently on productive systems.
|
|
|
1TGAP42XSITEONLY
|
Runtime/Operator/Engineering, site-only This license is intended for engineering and commissioning purposes for OEMs / plant builders. It is not permitted to be used permanently on productive systems.
|
|
|
1TGAP4XCDRV9992NEW
|
PROFIBUS DP/PROFINET/CTRL,NEW Driver license for PROFIBUS DP / PROFINET driver (per controller).
|
|
|
1TGAP4XCDRV9992OEM
|
PROFIBUS DP / PROFINET / CTRL,OEM Driver license for PROFIBUS DP / PROFINET driver (per controller).
|
|
|
1TGAP4XCDRV9992UPG
|
PROFIBUS DP / PROFINET / CTRL,UPG Driver license for PROFIBUS DP / PROFINET driver (per controller).
|
|
|
1TGAP4XCDRV9993NEW
|
Modbus RTU/TCP/CTRL/CC,NEW Driver license for Modbus RTU/TCP driver (per controller).
|
|
|
1TGAP4XCDRV9993OEM
|
Modbus RTU/TCP/CTRL/CC,OEM Driver license for Modbus RTU/TCP driver (per controller).
|
|
|
1TGAP4XCDRV9993UPG
|
Modbus RTU/TCP/CTRL/CC,UPG Driver license for Modbus RTU/TCP driver (per controller).
|
|
|
1TGAP4XCDRV9997NEW
|
S5/S7-TC/PIP/CTRL,NEW Driver license for S5/S7 TCP/IP driver (per controller).
|
|
|
1TGAP4XCDRV9997OEM
|
S5/S7-TC/PIP/CTRL,OEM Driver license for S5/S7 TCP/IP driver (per controller).
|
|
|
1TGAP4XCDRV9997UPG
|
S5/S7-TC/PIP/CTRL,UPG Driver license for S5/S7 TCP/IP driver (per controller).
|
|
|
1TGAP4XCDRV9998NEW
|
IEC 60870-5-104/CTRL/CC,NEW This license authorizes the use of the IEC 60870-5-104 driver on a B&R controller.
|
|
|
1TGAP4XCDRV9998OEM
|
IEC 60870-5-104/CTRL/CC,OEM This license authorizes the use of the IEC 60870-5-104 driver on a B&R controller.
|
|
|
1TGAP4XCDRV9998UPG
|
IEC 60870-5-104/CTRL/CC,UPG This license authorizes the use of the IEC 60870-5-104 driver on a B&R controller.
|
|
|
1TGAP4XCDRV9999NEW
|
IEC 60870-5-101/CTRL,NEW This license authorizes the use of the IEC 60870-5-101 driver on a B&R controller.
|
|
|
1TGAP4XCDRV9999OEM
|
IEC 60870-5-101/CTRL,OEM This license authorizes the use of the IEC 60870-5-101 driver on a B&R controller.
|
|
|
1TGAP4XCDRV9999UPG
|
IEC 60870-5-101/CTRL,UPG This license authorizes the use of the IEC 60870-5-101 driver on a B&R controller.
|
|
|
1TGAP4XCLIB9995NEW
|
MPC Signal (MIMO)/CTRL,NEW The license is valid for the activation of 1 controlled variable (X), 1 manipulated variable (Y) or 1 disturbance variable input (Z). 7 licenses are therefore required for an MPC with e.g. 2x X,3x Z,2x Y.
|
|
|
1TGAP4XCLIB9995OEM
|
MPC Signal (MIMO)/CTRL,OEM The license is valid for the activation of 1 controlled variable (X), 1 manipulated variable (Y) or 1 disturbance variable input (Z). 7 licenses are therefore required for an MPC with e.g. 2x X,3x Z,2x Y.
|
|
|
1TGAP4XCLIB9995UPG
|
MPC signal (MIMO)/CTRL,UPG The license is valid for the activation of 1 controlled variable (X), 1 manipulated variable (Y) or 1 disturbance variable input (Z). 7 MPC signal licenses are required for an MPC with e.g.2x X,3x Z and 2x Y!
|
|
|
1TGAP4XCLIB9997NEW
|
PAL Library/CTRL,NEW This license authorizes the use of the Process Automation Library (PAL) on a B&R controller.
|
|
|
1TGAP4XCLIB9997OEM
|
PAL Library/CTRL,OEM This license authorizes the use of the Process Automation Library (PAL) on a B&R controller.
|
|
|
1TGAP4XCLIB9997UPG
|
PAL Library/CTRL,UPG This license authorizes the use of the Process Automation Library (PAL) on a B&R controller.
|
|
|
1TGAP4XCLIB9998NEW
|
Basic library/CTRL,NEW This license authorizes the use of a B&R controller with complete engineering.
|
|
|
1TGAP4XCLIB9998OEM
|
Basic library/CTRL,OEM This license authorizes the use of a B&R controller with complete engineering.
|
|
|
1TGAP4XCLIB9998UPG
|
Basic library/CTRL,UPG This license authorizes the use of a B&R controller with complete engineering.
|
|
|
1TGAP4XCRED0000NEW
|
Controller redund./CTRL,NEW This license authorizes the use of controller redundancy on a B&R controller (required for primary and secondary).
|
|
|
1TGAP4XCRED0000OEM
|
Controller redund./CTRL,OEM This license authorizes the use of controller redundancy on a B&R controller (required for primary and secondary).
|
|
|
1TGAP4XCRED0000UPG
|
Controller redund./CTRL,UPG This license authorizes the use of controller redundancy on a B&R controller (required for primary and secondary).
|
|
|
1TGAP4XE0000000NEW
|
Engineering,NEW The engineering system is used to create configuration data for the entire project before it is distributed to the runtime server, operator station and controller / field device target systems.
|
|
|
1TGAP4XE0000000OEM
|
Engineering,OEM The engineering system is used to create configuration data for the entire project before it is distributed to the runtime server, operator station and controller / field device target systems.
|
|
|
1TGAP4XE0000000UPG
|
Engineering,UPG The engineering system is used to create configuration data for the entire project before it is distributed to the runtime server, operator station and controller / field device target systems.
|
|
|
1TGAP4XEAR-2020NEW
|
RTOS - Security updates 2020/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2020-01-01 to 2020-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2021NEW
|
RTOS - Security updates 2021/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2021-01-01 to 2021-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2022NEW
|
RTOS - Security updates 2022/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2022-01-01 to 2022-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2023NEW
|
RTOS - Security updates 2023/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2023-01-01 to 2023-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2024NEW
|
RTOS - Security updates 2024/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2024-01-01 to 2024-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2025NEW
|
RTOS - Security updates 2025/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2025-01-01 to 2025-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAR-2026NEW
|
RTOS - Security updates 2026/ E Includes a 1-year subscription for RTOS security updates from B&R as an AR upgrade. The subscription starts in the period from 2026-01-01 to 2026-12-31 and ends after 12 months. Note: The service life of the updated AR (RTOS = Automation Runtime) is not limited. One (1) license is required per installed engineering server (E).
|
|
|
1TGAP4XEAS-0000NEW
|
Engin. AS edition APROL,NEW Enables the creation of the controller hardware configuration and configuration of the fieldbuses.
|
|
|
1TGAP4XEAS-0000OEM
|
Engin. AS edition APROL,OEM Enables the creation of the controller hardware configuration and configuration of the fieldbuses.
|
|
|
1TGAP4XO0000000NEW
|
Operator,NEW The operator station provides the user interface for the operators (process graphics, faceplates, trend displays, alarm and event lists, etc.).
|
|
|
1TGAP4XO0000000OEM
|
Operator,OEM The operator station provides the user interface for the operators (process graphics, faceplates, trend displays, alarm and event lists, etc.).
|
|
|
1TGAP4XO0000000UPG
|
Operator,UPG The operator station provides the user interface for the operators (process graphics, faceplates, trend displays, alarm and event lists, etc.).
|
|
|
1TGAP4XONET0001NEW
|
Operator via Net, NEW Enables the operation of an operator station via remote access (VNC client, etc.)
|
|
|
1TGAP4XONET0001OEM
|
Operator via Net, OEM Enables the operation of an operator station via remote access (VNC client, etc.)
|
|
|
1TGAP4XONET0001UPG
|
Operator via Net, UPG Enables the operation of an operator station via remote access (VNC client, etc.)
|
|
|
1TGAP4XR0001111NEW
|
ParameterCenter,NEW Enables operation of the ParameterCenter for parameter management (recipe management).
|
|
|
1TGAP4XR0001111OEM
|
ParameterCenter,OEM Enables operation of the ParameterCenter for parameter management (recipe management).
|
|
|
1TGAP4XR0001111UPG
|
ParameterCenter,UPG Enables operation of the ParameterCenter for parameter management (recipe management).
|
|
|
1TGAP4XRGV-0050NEW
|
GV-Lic-R 0050 GVs,NEW GV license for the non-redundant runtime server, for 0050 gateway variable data points.
|
|
|
1TGAP4XRGV-0050OEM
|
GV-Lic-R 0050 GVs,OEM GV license for the non-redundant runtime server, for 0050 gateway variable data points.
|
|
|
1TGAP4XRGV-0050UPG
|
GV-Lic-R 0050 GVs,UPG GV license for the non-redundant runtime server, for 0050 gateway variable data points.
|
|
|
1TGAP4XRGV-1000NEW
|
GV-Lic-R 1000 GVs,NEW GV license for the non-redundant runtime server, for 1000 gateway variable data points.
|
|
|
1TGAP4XRGV-1000OEM
|
GV-Lic-R 1000 GVs,OEM GV license for the non-redundant runtime server, for 1000 gateway variable data points.
|
|
|
1TGAP4XRGV-1000UPG
|
GV-Lic-R 1000 GVs,UPG GV license for the non-redundant runtime server, for 1000 gateway variable data points.
|
|
|
1TGAP4XRGV-5000NEW
|
GV-Lic-R 5000 GVs,NEW GV license for the non-redundant runtime server, for 5000 gateway variable data points.
|
|
|
1TGAP4XRGV-5000OEM
|
GV-Lic-R 5000 GVs,OEM GV-Lizenz für den nicht-redundanten Runtime Server, für 5000 Gateway-Variablen-Datenpunkte.
|
|
|
1TGAP4XRGV-5000UPG
|
GV-Lic-R 5000 GVs,UPG GV license for the non-redundant runtime server, for 5000 gateway variable data points.
|
|
|
1TGAP4XRIO-0050NEW
|
I/O-Lic-R 0050 I/OS,NEW I/O license for the non-redundant runtime server for 0050 I/O data points.
|
|
|
1TGAP4XRIO-0050OEM
|
I/O-Lic-R 0050 I/Os,OEM I/O license for the non-redundant runtime server for 0050 I/O data points.
|
|
|
1TGAP4XRIO-1000NEW
|
I/O-Lic-R 1000 I/Os,NEW I/O license for the non-redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRIO-1000OEM
|
I/O-Lic-R 1000 I/Os,OEM I/O license for the non-redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRIO-1000UPG
|
I/O-Lic-R 1000 I/Os,UPG I/O license for the non-redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRIO-5000NEW
|
I/O-Lic-R 5000 I/Os,NEW I/O license for the non-redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRIO-5000OEM
|
I/O-Lic-R 5000 I/Os,OEM I/O license for the non-redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRIO-5000UPG
|
I/O-Lic-R 5000 I/Os,UPG I/O license for the non-redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRLIB9996NEW
|
PAL Lib Edition PDA/CTRL,NEW4X This license authorizes the use of the Process Automation Library (PAL) on a B&R control computer (PDA coupling).
|
|
|
1TGAP4XRLIB9996OEM
|
PAL Lib Edition PDA/CTRL,OEM4X This license authorizes the use of the Process Automation Library (PAL) on a B&R control computer (PDA coupling).
|
|
|
1TGAP4XRLIB9996UPG
|
PAL Lib Edition PDA/CTRL,UPG4X This license authorizes the use of the Process Automation Library (PAL) on a B&R control computer (PDA coupling).
|
|
|
1TGAP4XRNET1111NEW
|
SQL access Historian DB,NEW Driver license for SQL access to APROL historical data.
|
|
|
1TGAP4XRNET1111OEM
|
SQL access Historian DB,OEM Driver license for SQL access to APROL historical data.
|
|
|
1TGAP4XRNET1111UPG
|
SQL access Historian DB,UPG Driver license for SQL access to APROL historical data.
|
|
|
1TGAP4XRNET1112NEW
|
OPC access RT database,NEW Driver license for OPC access to the real-time database
|
|
|
1TGAP4XRNET1112OEM
|
OPC access RT database,OEM Driver license for OPC access to the real-time database
|
|
|
1TGAP4XRNET1112UPG
|
OPC access RT database,UPG Driver license for OPC access to the real-time database
|
|
|
1TGAP4XRRED0000NEW
|
RTS redundancy capability/RTS,NEW The RTS redundancy capability license for the runtime server (RTS) enables redundant operation of a runtime server to increase system availability. For a redundant runtime server, two runtime server licenses (1x master/ 1x slave) and two RTS redundancy capability licenses (1x master/ 1x slave) are required.
|
|
|
1TGAP4XRRED0000OEM
|
RTS redundancy capability/RTS,OEM The RTS redundancy capability license for the runtime server (RTS) enables redundant operation of a runtime server to increase system availability. For a redundant runtime server, two runtime server licenses (1x master/ 1x slave) and two RTS redundancy capability licenses (1x master/ 1x slave) are required.
|
|
|
1TGAP4XRRED0000UPG
|
RTS redundancy capability/RTS,UPG The RTS redundancy capability license for the runtime server (RTS) enables redundant operation of a runtime server to increase system availability. For a redundant runtime server, two runtime server licenses (1x master/ 1x slave) and two RTS redundancy capability licenses (1x master/ 1x slave) are required.
|
|
|
1TGAP4XRRGV0050NEW
|
GV-Lic-rRCap 0050 GVs,NEW GV license for redundancy capability, for the redundant runtime server, for 0050 gateway variable data points.
|
|
|
1TGAP4XRRGV0050OEM
|
GV-Lic-rRCap 0050 GVs,OEM GV license for redundancy capability, for the redundant runtime server, for 0050 gateway variables-data point.
|
|
|
1TGAP4XRRGV1000NEW
|
GV-Lic-rRCap 1000 GVs,NEW GV license for redundancy capability, for the redundant runtime server, for 1000 gateway variable data points.
|
|
|
1TGAP4XRRGV1000OEM
|
GV-Lic-rRCap 1000 GVs,OEM GV license for redundancy capability, for the redundant runtime server, for 1000 gateway variable data points.
|
|
|
1TGAP4XRRGV5000NEW
|
GV-Lic-rRCap 5000 GVs,NEW GV license for redundancy capability, for the redundant runtime server, for 5000 gateway variable data points.
|
|
|
1TGAP4XRRGV5000OEM
|
GV-Lic-rRCap 5000 GVs,OEM GV license for redundancy capability, for the redundant runtime server, for 5000 gateway variable data points.
|
|
|
1TGAP4XRRIO0050NEW
|
I/O-Lic-rRCap 0050 I/Os,NEW I/O license for redundancy capability,, for the redundant runtime server for 0050 I/O data points.
|
|
|
1TGAP4XRRIO0050OEM
|
I/O-Lic-rRCap 0050 I/Os,OEM I/O license for redundancy capability,, for the redundant runtime server for 0050 I/O data points.
|
|
|
1TGAP4XRRIO0050UPG
|
I/O-Lic-rRCap 0050 I/Os,UPG I/O license for redundancy capability,, for the redundant runtime server for 0050 I/O data points.
|
|
|
1TGAP4XRRIO1000NEW
|
I/O-Lic-rRCap 1000 I/Os,NEW I/O license for redundancy capability,, for the redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRRIO1000OEM
|
I/O-Lic-rRCap 1000 I/Os,OEM I/O license for redundancy capability,, for the redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRRIO1000UPG
|
I/O-Lic-rRCap 1000 I/Os,UPG I/O license for redundancy capability,, for the redundant runtime server for 1000 I/O data points.
|
|
|
1TGAP4XRRIO5000NEW
|
I/O-Lic-rRCap 5000 I/Os,NEW I/O license for redundancy capability,, for the redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRRIO5000OEM
|
I/O-Lic-rRCap 5000 I/Os,OEM I/O license for redundancy capability,, for the redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRRIO5000UPG
|
I/O-Lic-rRCap 5000 I/Os,UPG I/O license for redundancy capability,, for the redundant runtime server for 5000 I/O data points.
|
|
|
1TGAP4XRSVR0000NEW
|
Runtime server,NEW The runtime server provides the runtime core functions of the system (alarm system, trend system, real-time database).
|
|
|
1TGAP4XRSVR0000OEM
|
Runtime server,OEM The runtime server provides the runtime core functions of the system (alarm system, trend system, real-time database).
|
|
|
1TGAP4XRSVR0000UPG
|
Runtime server,UPG The runtime server provides the runtime core functions of the system (alarm system, trend system, real-time database).
|
|
|
1TGAP4XXBI-9990SU2
|
BI platform Jasper RS,SU2 Subscription from Cloud Software Group Inc. to unlock JasperReports Server. The 2-year subscription starts with delivery to B&R. This results in a duration of 1.5 years after delivery to the customer.
|
|
|
1TGAP4XXOS-0000SU2
|
Operating system + 3rd-party licenses per CC Includes two SUSE Linux Enterprise Server (SLE) OEM licenses (support through B&R only) and other installed OEM licenses. The SLE license is of type SUSE Linux Enterprise Server, x86 and x86-64, 1-2 sockets or 1-2 virtual machines, basic subscription, 1 year. This ensures a maximum period of 2 years for B&R security updates via APROL AutoYaST Update. The subscription begins after delivery by B&R. The useful life of SLES is not limited, but a valid subscription is required for update rights.
|
|
|
1TGAP4XXOS-0000SU4
|
Operating system + 3rd-party licenses per CC Includes four SUSE Linux Enterprise Server (SLE) OEM licenses (support through B&R only) and other installed OEM licenses. The SLE license is of type SUSE Linux Enterprise Server, x86 and x86-64, 1-2 sockets or 1-2 virtual machines, basic subscription, 1 year. This ensures a maximum period of 4 years for B&R security updates via APROL AutoYaST Update. The subscription begins after delivery by B&R. The useful life of SLES is not limited, but a valid subscription is required for update rights.
|
|
|
1TGAP4XXOS-2021NEW
|
GPOS - Security update- 2021/ CC
|
|
|
1TGAP4XXOS-2022NEW
|
GPOS - Security update- 2022/ CC
|
|
|
1TGAP4XXOS-2023NEW
|
GPOS - Security update- 2023/ CC
|
|
|
1TGAP4XXOS-2024NEW
|
GPOS - Security update- 2024/ CC
|
|
|
1TGAP4XXOS-2025NEW
|
GPOS - Security update- 2025/ CC
|
|
|
1TGAP4XXOS-2026NEW
|
GPOS - Security update- 2026/ CC
|
|
|
1TGMPASSET.20-01
|
mapp Asset Intensity calculates the effectiveness of a machine based on its production data. The calculated data is then prepared for display in the form of a list or graph or made available for export.
|
|
|
1TGMPAUDIT.02
|
B&R software license - MpAudit - Single license - Records various events (user management, alarm management, OPC UA, etc.) - Archival and export in various formats (encrypted .zip archive, readable PDF, etc.) - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPAUDIT.10-01
|
mapp Audit collects and manages a wide range of different events. These include when user-defined events occur, when machine operators log in/out or when an alarm occurs. All events are collected and can be exported with password protection to protect them from tampering.
|
|
|
1TGMPAXFLAT.10-01
|
Contains all licenses for mapp Axis advanced ACOPOS P3 features. License only required for ACOPOS P3.
|
|
|
1TGMPAXIS.00-01
|
The mapp Axis "Basic" license allows the use of mapp Axis on the target system. It is required if axis functionality is used. Only one license is required per target system.
|
|
|
1TGMPBCKLSH.10-01
|
More precise positioning of spindle drives with and without backlash. License required for ACOPOS P3.
|
|
|
1TGMPBRCLNT.10-01
|
License for one additional client on B&R hardware.
|
|
|
1TGMPCLIENT.10-01
|
License for one additional client.
|
|
|
1TGMPCNC.00-01
|
This license allows the use of Cartesian mechanical systems. The maximum number of path-controlled axes is 4. One license is required per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNC.02
|
B&R software license - MpCnc - Single license - CNC functional interface for Cartesian systems - Starting programs, moving/jogging blocks, etc. - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative. The license for the CNC channel must be ordered separately.
|
|
|
1TGMPCNC4.00-01
|
This license allows the use of a mechanical system with up to 4 axes. The maximum number of path-controlled axes is 4. One license is required per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNC4X.00-01
|
This license makes it possible to use a mechanical system with up to four axes. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNC5X.00-01
|
This license makes it possible to use a mechanical system with up to five axes. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNC6X.00-01
|
This license makes it possible to use a mechanical system with up to six axes. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNCCDC.10-01
|
This license allows the use of tool radius compensation. One license is required for each axis group.
|
|
|
1TGMPCNCCOMP.10-01
|
This license allows the use of compressor technology. One license is required for each axis group.
|
|
|
1TGMPCNCFLAT.00-01
|
This license makes it possible to use any number of axis groups (of all types) on a target system. An unlimited number of path-controlled axes per axis group is possible. Only one license is necessary per target system; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCNCGEOC.10-01
|
This license allows the use of geometric compensation. One license is required for each axis group.
|
|
|
1TGMPCNCJERK.10-01
|
This license allows the use of a jerk-limited path planner. One license is required for each axis group.
|
|
|
1TGMPCNCPMF.10-01
|
This license allows the use of programmed moving frames. One license is necessary for each axis group.
|
|
|
1TGMPCNCWSM.10-01
|
This license allows the use of workspace monitoring. One license is required for each axis group.
|
|
|
1TGMPCNCX.00-01
|
This license makes it possible to use a Cartesian mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPCODEBOX.10-01
|
mapp CodeBox makes it possible to program directly at the machine via the HMI application. The behavior of the machine can thus be changed without an additional engineering tool. There is basic access via Ladder Diagram and high-level language access via Structured Text.
|
|
|
1TGMPCONTROL.00-01
|
This license includes advanced functions in closed-loop control and signal processing. This includes areas such as autotuning, system identification, statistical data evaluation and profile generation.
|
|
|
1TGMPCUSMEC.00-01
|
This license makes it possible to use a custom mechanical system. The maximum number of path-controlled axes is 4. One license is necessary per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPDATA.02
|
B&R software license - MpData - Single license - Traces variable values during runtime - Records on value change, trigger or time interval - Dynamic variable mapping at runtime - Data archival in CSV file(s) - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPDATA.10-01
|
mapp Data makes it possible log process data. The user defines the process data and the time frame in which it should be collected. In addition, data can be displayed in table form or evaluated statistically.
|
|
|
1TGMPDB.20-01
|
mapp Database makes it possible to connect to a database. You can write data to the database or read data from the database.
|
|
|
1TGMPDELTA.00-01
|
This license allows the use of a delta mechanical system. The maximum number of path-controlled axes is 4. One license is required per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPDELTA.02
|
B&R software license - MpDelta - Single license - Delta robot interface - Starting programs, jogging, etc. - Various coordinate systems - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative. The license for the CNC channel and transformation must be ordered separately.
|
|
|
1TGMPDELTAX.00-01
|
This license makes it possible to use a delta mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPDS402.20-01
|
The mapp Axis "DS402-compliant drive" license allows the use of DS402-compatible drives via POWERLINK. One license is required for each axis.
|
|
|
1TGMPELS.10-01
|
More precise closed-loop control of flexible drive systems with model-based control and integrated virtual sensors. License required for ACOPOS P3.
|
|
|
1TGMPENERGY.02
|
B&R software license for MpEnergy - Single-user license - Collect energy and power data - Display energy and power data via HMI application - Integrate external energy consumers - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPENERGY.10-01
|
mapp Energy collects energy data from various modules in the machine and prepares the data so that energy consumption can be visualized. In addition, data is collected and made available as a file for analysis.
|
|
|
1TGMPFLAT.02
|
- mapp technology flatrate included "1TGMPYYYY.02" single licenses per PLC - Future "1TGMPYYYY.02" single licenses are also covered
|
|
|
1TGMPHYD.00-01
|
mapp Hydraulics provides a simple approach to optimizing closed-loop control of a wide range of hydraulic systems. By configuring all hydraulic components, such as pumps, valves and cylinders, the hydraulic system can be clearly displayed. Self-adjusting controllers ensure high control quality. Integrated simulation enables fast virtual commissioning.
|
|
|
1TGMPISQRIP.10-01
|
Compensation for motor-specific disturbances. License required for ACOPOS P3.
|
|
|
1TGMPOEE.02
|
B&R software license - MpOee - Single license - Records overall equipment effectiveness (KPI) for measuring productivity - Display of measured values as list, timeline or graph - Export of measured values in CSV format - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPOEE.10-01
|
mapp OEE calculates overall equipment effectiveness based on the performance, availability and quality of the machine. The calculated data is then prepared for display in the form of a list or graph or made available for export.
|
|
|
1TGMPPACKML.02
|
B&R software license - MpPackML - Single license - OMAC PackML state model - Configuration of states for each operating mode - Support for several operating modes - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPPACKML.10-01
|
mapp PackML provides support when implementing the OMAC PackML standard. Special focus is placed on the state model as well as managing the various operating modes. In addition, the current machine state can be shared with other machines/stations in the network using PackTags.
|
|
|
1TGMPPAPER.20-01
|
Widget "Paper" is based on SVG technology and makes it possible to implement animations, transitions and transformations in a mapp View HMI application to show the machine process in motion.
|
|
|
1TGMPPLAST.00-01
|
Base license for mapp Plastics This license is required to use the advanced functions in the mapp Control Technology Package that are related to machines in the plastics industry. The license includes mapp Clamp (operation of a clamp), mapp Inject (operation of injection and plasticizing equipment), mapp Ejector (operation of an ejector), mapp InjUnit (operation of an injection unit) and other basic functions for these types of machines.
|
|
|
1TGMPPMPHP.10-01
|
The "High-performance" auxiliary feature of the servo pump controller enables decentralized pressure and speed control on an ACOPOS servo drive. Short sampling times and very short reaction times enable minimal pressure overshoot and highly dynamic pressurization. This makes it possible to achieve the highest performance in terms of pressure control.
|
|
|
1TGMPPMPPROT.10-01
|
Using the pump protection feature of the servo pump controller, a servo pump can be protected against thermal overheating. This enables energy-efficient operation in the low speed range. Due to the additional shutdown protection for motor and drive, it is also possible to operate both briefly in overload mode to cover peak loads without causing an undesirable shutdown of the servo pump.
|
|
|
1TGMPPMPTUNE.10-01
|
The innovative autotuning feature from mapp Hydraulics can identify the hydraulic system relevant for servo pump control at any time and then determine the optimal pressure and speed control parameters. This guarantees the highest possible control quality and allows the hydraulic system to operate at its limits.
|
|
|
1TGMPREACT.10-01
|
User-specific functions directly on the drive with low cycle time. License required for ACOPOS P3.
|
|
|
1TGMPREPCTRL.10-01
|
Automatic compensation of lag error caused by periodic disturbances. License required for ACOPOS P3.
|
|
|
1TGMPREPORT.20-01
|
mapp Report makes it possible to generate PDF reports directly at the machine. A wide range of data can be included in the report, such as diagnostic data or current production values. These reports can then be localized and exported in a user-specified design.
|
|
|
1TGMPROBCDC.10-01
|
This license allows the use of cutter diameter compensation. One license is necessary for each axis group.
|
|
|
1TGMPROBCNC.10-01
|
Лицензия для mapp Robotics и mapp CNC 4+ "Premium" включает одну группу осей, но не ограничено по количеству осей управляемых по траектории. mapp Axis "Premium" включает в себя функцию управления осью по траектории. Требуется одна лицензия для каждой целевой системы. Эта лицензия подлежит экспортным ограничениям двойного назначения ЕС Регламент (ЕС) 428/2009.
|
|
|
1TGMPROBCNC.20-01
|
mapp Robotics/CNC 4+ и mapp CNC "Ultimate" не ограничено по количеству групп осей и не ограничено по количеству осей управляемых по траектории. mapp Axis "Ultimate" включает в себя функцию управления осью по траектории. Требуется одна лицензия для каждой целевой системы. На эту лицензию распространяются экспортные ограничения о продукции двойного назначения согласно Постановления ЕС 428/2009.
|
|
|
1TGMPROBFF.10-01
|
This license allows the use of feed-forward control based on a dynamic model. One license is necessary for each axis group.
|
|
|
1TGMPROBFLAT.00-01
|
This license makes it possible to use any number of axis groups (of all types) on a target system. An unlimited number of path-controlled axes per axis group is possible. Only one license is necessary per target system; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPROBO4.00-01
|
This license allows the use of a 4-axis robotic arm mechanical system. The maximum number of path-controlled axes is 4. One license is required per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPROBO4X.00-01
|
This license makes it possible to use a 4-axis robotic arm mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPROBO5X.00-01
|
This license makes it possible to use a 5-axis robotic arm mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPROBO6X.00-01
|
This license makes it possible to use a 6-axis robotic arm mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPROBOARM.02
|
B&R software license - MpRoboArm - Single license - Interface for serial robot kinematics (anthropomorphic) - Starting programs, jogging, etc. - Various coordinate systems - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative. The license for the CNC channel and transformation must be ordered separately.
|
|
|
1TGMPROBOX.02
|
B&R software license - MpRoboX - Single license - Flexible use of various robot kinematics - Starting programs, jogging, etc. - Various coordinate systems - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative. The license for the CNC channel and transformation must be ordered separately.
|
|
|
1TGMPROBPMF.10-01
|
This license allows the use of programmed moving frames. One license is necessary for each axis group.
|
|
|
1TGMPSAFETYX.00-01
|
B&R software license MpSafetyX - Single license - For interacting with B&R safety components - Provides secure data exchange between HMI elements and the SafeLOGIC controller - Transfer of safe parameters from an HMI application to the safe application - Support for modular software concepts - Web-based diagnostics and XML configuration
|
|
|
1TGMPSCARA.00-01
|
This license allows the use of a SCARA mechanical system. The maximum number of path-controlled axes is 4. One license is required per axis group. Included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPSCARA.02
|
B&R software license - MpScara - Single license - SCARA robot interface - Starting programs, jogging, etc. - Various coordinate systems - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative. The license for the CNC channel and transformation must be ordered separately.
|
|
|
1TGMPSCARAX.00-01
|
This license makes it possible to use a SCARA mechanical system. There is no restriction on the number of path-controlled axes. One license is necessary per axis group; it is subject to the dual-use export restrictions per Regulation (EC) No. 2021/821 of the European Community. Also included is the functionality of mapp Axis basic license 1TGMPAXIS.00-01.
|
|
|
1TGMPSEQ.20-01
|
mapp Sequence makes it possible to implement dynamic machine sequences. It allows the operator to influence the production sequence as needed directly via the machine's HMI application without having to change the software.
|
|
|
1TGMPSMCADV.10-01
|
This license activates the use of the "openSAFETY advanced extension set" for SafeMOTION. License required for ACOPOS P3.
|
|
|
1TGMPSMCPOS.10-01
|
This license activates the use of the "openSAFETY encoder basic set" for SafeMOTION. License required for ACOPOS P3.
|
|
|
1TGMPSMCVEL.10-01
|
This license activates the use of the "openSAFETY speed extension set" for SafeMOTION. License required for ACOPOS P3.
|
|
|
1TGMPSPINDLE.02
|
B&R software license - MpSpindle - Single license - Axis spindle functionality - Interface to handheld operating device - Interface to CNC program - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPSRV.00-01
|
Basic license for mapp Services Required to use extended functions of the mapp Technology Package. This license includes mapp AlarmX (alarm management), mapp IO (dynamic hardware configuration), mapp User (user management), mapp Alarm (alarm management with reference to VC4), mapp File (file explorer), mapp Skyline (visualization of a machine line in combination with a mapp View widget), mapp J1939 (SAE J1939 protocol) and mapp Recipe (recipe management).
|
|
|
1TGMPTEMP.10-01
|
mapp Temperature provides functions for optimal control of temperature processes. Requirements such as autotuning controllers, zone-synchronous heating profiles, minimum overshoot or multi-zone control for heating and cooling processes can be easily configured.
|
|
|
1TGMPTRKCOLL.10-01
|
This license makes it possible to use variable collision avoidance. This type of collision avoidance is characterized by the fact that the minimum spacing between shuttles depends on their current positions. In general, it therefore allows reduced spacing. One license is necessary for each assembly.
|
|
|
1TGMPTWEET.20-01
|
mapp Tweet makes it possible to transmit messages directly from the machine. This allows service technicians to be informed of emergencies involving the machine via SMS text message. Quick responses to critical situations are possible via a direct connection to mapp AlarmX.
|
|
|
1TGMPUSER.02
|
B&R software license - MpUser - Single license - User and group management - Password management (e.g. expiration date) - Password encryption - Import and export of users and groups - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPUSERX.02
|
B&R software license - MpUserX - Single license - User and role management - Password management (e.g. expiration date) - Password encryption - Import and export of users and roles - Support for modular software concepts - Web-based diagnostics and XML configuration The use of mapp flat-rate 1TGMPFLAT.02 is possible as an alternative.
|
|
|
1TGMPUSERX.10-01
|
mapp UserX allows the implementation of user management based on the Automation Studio user role system. This includes logging in/out, creating and editing users and saving additional user data (e.g. telephone numbers). Changes to user data can also be recorded as audit events.
|
|
|
1TGMPVIEW.00-01
|
Contains mapp View server, one client license and a standard set of widgets
|
|
|
1TGMPVISION.00-01
|
The mapp Vision basic license makes it possible to access various machine vision functions such as: - CodeReader - ModelBasedBlob - Matching - ...
|
|
|
1TGMPVNCVIEW.20-01
|
This widget establishes a connection to a VNC server and displays its contents in the web-based mapp View HMI application.
|
|
|
1TGMPWEBH.00-01
|
mapp Web Handling offers a solution for closed-loop tension control of complete web processing machines. It covers the rewinding and unwinding process as well as the tension and dancer control of every zone. Integrated simulation allows the project to be commissioned without a real plant.
|
|
|
1TGSIMTS.CRP.00-01
|
Корпоративная лицензия позволяет использовать Automation Studio Target for Simulink всеми пользователями компании во всех офисах компании, в том числе и в ассоциированных компаниях, в течение одного года. В соответствии с корпоративной лицензией право на использование Automation Studio на Automation PC компании B&R, которое поставляется совместно с аппаратным обеспечением, может быть предоставлено, если гарантируется использование Automation Studio только техническим персоналом пользователя, работающим с аппаратным обеспечением, или производителям установки. Automation Studio Target for Simulink обеспечивает автоматическую генерацию кода из MATLAB / Simulink for Automation Studio. Поддержка C, C++ и функциональных блоков. Также поддерживаются режим Simulink external mode, функции Simulink C-S, привязка модели и SimScape . Лицензирование происходит при активации продукта через Интернет. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSIMTS.SNG.00-01
|
Однопользовательская лицензия позволяет только одному пользователю использовать Automation Studio Target for Simulink в любой момент времени в течение одного года. Automation Studio Target for Simulink обеспечивает автоматическую генерацию кода из MATLAB / Simulink для Automation Studio. Поддержка C, C++ и функциональных блоков. Nакже поддерживаются режим Simulink external mode, функции Simulink C-S, привязка модели и SimScape . Лицензия размещается на аппаратном ключе Technology Guard (TG). В случае использования аппаратного ключа несколько пользователей могут предоставлять друг другу право на использование Automation Studio на разных рабочих станциях, подключая ключ (TG) с однопользовательской лицензией к соответствующей рабочей станции. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия. Аппаратный ключ Technology Guard не входит в поставку однопользовательской лицензии и заказывается отдельно.
|
|
|
1TGSIMTS.SNG.00-02
|
Однопользовательская лицензия позволяет одному пользователю использовать Automation Studio Target for Simulink в любой момент времени в течение одного года. Automation Studio Target for Simulink обеспечивает автоматическую генерацию кода из MATLAB / Simulink для Automation Studio. Поддержка C, C++ и функциональных блоков. Nакже поддерживаются режим Simulink external mode, функции Simulink C-S, привязка модели и SimScape . Лицензия хранится в контейнере лицензий, который привязывается к компьютеру. Перенос лицензии на другой компьютер невозможен. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSIMTS.STE.00-01
|
Лицензия Automation Studio Target for Simulink на локальное использование дает доступ любому количеству пользователей, но в пределах одного офиса или предприятия. Пользователи должны быть официально трудоустроены в компании, однако могут использовать Automation Studio вне зависимости от своего местонахождения как, например, международные специалисты по техническому обслуживанию. Automation Studio Target for Simulink обеспечивает автоматическую генерацию кода из MATLAB / Simulink для Automation Studio. Поддержка C, C++ и функциональных блоков. Также поддерживаются режим Simulink external mode, функции Simulink C-S, привязка модели и SimScape . Лицензирование происходит при активации продукта через Интернет. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSWAS.CRP.00-01
|
Корпоративная лицензия позволяет использовать Automation Studio всеми пользователями компании во всех офисах компании, в том числе и в ассоциированных компаниях, в течение одного года. В соответствии с корпоративной лицензией право на использование Automation Studio на Automation PC компании B&R, которое поставляется совместно с аппаратным обеспечением, может быть предоставлено, если гарантируется использование Automation Studio только техническим персоналом пользователя, работающим с аппаратным обеспечением, или производителям установки. Лицензирование происходит при активации продукта через Интернет. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSWAS.SNG.00-01
|
Однопользовательская лицензия позволяет только одному пользователю использовать Automation Studio в любой момент времени в течение одного года. Лицензия размещается на аппаратном ключе Technology Guard (TG). В случае использования аппаратного ключа несколько пользователей могут предоставлять друг другу право на использование Automation Studio на разных рабочих станциях, подключая ключ (TG) с однопользовательской лицензией к соответствующей рабочей станции. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия. Аппаратный ключ Technology Guard не входит в поставку однопользовательской лицензии и заказывается отдельно.
|
|
|
1TGSWAS.SNG.00-02
|
Однопользовательская лицензия позволяет только одному пользователю использовать Automation Studio в любой момент времени в течение одного года. Лицензия хранится в контейнере лицензий, который привязывается к компьютеру. Перенос лицензии на другой компьютер невозможен. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSWAS.SNG.01-02
|
Лицензия на перепродажу представляет собой однопользовательскую лицензию. Она предназначена исключительно для перепродажи операторам машин и установок. Такая лицензия позволяет проводить техническое обслуживание и диагностику существующих машин и систем, а также их программного обеспечения. Лицензия хранится в контейнере лицензий, который привязывается к компьютеру. Перенос лицензии на другой компьютер невозможен. Эта лицензия предоставляется на неограниченный срок. Создание новых проектов и обновления из Интернета не поддерживаются.
|
|
|
1TGSWAS.STE.00-01
|
Лицензия Automation Studio на локальное использование дает доступ любому количеству пользователей, но в пределах одного предприятия. Пользователи должны быть приняты на работу по месту нахождения соответствующей компании, однако могут использовать Automation Studio вне зависимости от своего местонахождения (например, международные специалисты по техническому обслуживанию). Лицензирование происходит при активации продукта через Интернет. Через год лицензия будет автоматически продлена на один год и будет автоматически сгенерирован счет на оплату продления лицензии, если лицензия не будет аннулирована до истечения срока ее действия.
|
|
|
1TGSWAS.STE.E0-01
|
Это лицензия Automation Studio, право на использование которой предоставляется любому количеству пользователей для образовательных и исследовательских целей по месту нахождения объекта, в котором проводится обучение. Срок действия Образовательной лицензии автоматически истекает через 400 календарных дней и не подлежит продлению. Лицензия также предусматривает использование ПО на личных компьютерах студентов, если это разрешено и согласовано с учебным заведением. Использование Образовательной лицензии в коммерческих целях запрещено.
|
|